module_universal_io/shared/freemodbus/port/portserial.c

#include "at32f403a_407.h"
//#include "at32f403a_407_board.h"
//#include "at32f403a_407_clock.h"
#include "FreeRTOS.h"
#include "task.h"
#include "mb.h"
#include "port.h"
#include "mbport.h"
#include <stdlib.h>

#define USART_INVALID_PORT      ( 0xFF )



void vMBPortSerialEnable( BOOL xRxEnable, BOOL xTxEnable )
{
    if (xRxEnable) {
        usart_interrupt_enable(USART3, USART_RDBF_INT, TRUE);
	}
	else {
        usart_interrupt_enable(USART3, USART_RDBF_INT, FALSE);
	}
	if (xTxEnable) {
        usart_interrupt_enable(USART3, USART_TDC_INT, TRUE);
	}
	else {
        usart_interrupt_enable(USART3, USART_TDC_INT, FALSE);
	}
}


BOOL xMBPortSerialInit( UCHAR ucPORT, ULONG ulBaudRate, UCHAR ucDataBits, 
                   eMBParity eParity, unsigned int stop_bit )
{
    gpio_init_type gpio_init_struct;
    usart_parity_selection_type parity;
    usart_data_bit_num_type data_bits;
    usart_stop_bit_num_type stop_bits;

    crm_periph_clock_enable(CRM_USART3_PERIPH_CLOCK, TRUE);
    crm_periph_clock_enable(CRM_GPIOD_PERIPH_CLOCK, TRUE);
    crm_periph_clock_enable(CRM_IOMUX_PERIPH_CLOCK, TRUE);
    gpio_pin_remap_config(USART3_GMUX_0011, TRUE);
    
    gpio_default_para_init(&gpio_init_struct);

    // configure the uart tx pin
    gpio_init_struct.gpio_drive_strength = GPIO_DRIVE_STRENGTH_STRONGER;
    gpio_init_struct.gpio_out_type  = GPIO_OUTPUT_PUSH_PULL;
    gpio_init_struct.gpio_mode = GPIO_MODE_MUX;
    gpio_init_struct.gpio_pins = GPIO_PINS_8;
    gpio_init_struct.gpio_pull = GPIO_PULL_NONE;
    gpio_init(GPIOD, &gpio_init_struct);

    switch (eParity)
	{
		case MB_PAR_NONE :
            parity = USART_PARITY_NONE;
            data_bits = USART_DATA_8BITS;
			break;
		case MB_PAR_ODD :
            parity = USART_PARITY_ODD;
            data_bits = USART_DATA_9BITS;
			break;
		case MB_PAR_EVEN :
            parity = USART_PARITY_EVEN;
            data_bits = USART_DATA_9BITS;
			break;
		default :
			return FALSE;
	}

    switch (stop_bit)
    {
        case 1 :
            stop_bits = USART_STOP_1_BIT;
        break;
        
        case 3 :
            stop_bits = USART_STOP_2_BIT;
        break;
        
        default :
            return FALSE;
    }
    
    
    // configure uart param
    usart_init(USART3, ulBaudRate, data_bits, stop_bits);
    usart_parity_selection_config(USART3, parity);
    usart_transmitter_enable(USART3, TRUE);
    usart_receiver_enable(USART3, TRUE);
    nvic_priority_group_config(NVIC_PRIORITY_GROUP_4);
    nvic_irq_enable(USART3_IRQn, 5, 0);
    usart_interrupt_enable(USART3, USART_RDBF_INT, TRUE);
    usart_interrupt_enable(USART3, USART_TDC_INT, TRUE);
    usart_enable(USART3, TRUE);  
  
    
    
#if 0  
	GPIO_InitTypeDef GPIO_InitStruct = {0};
    
    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;

    __HAL_RCC_USART4_FORCE_RESET();
    __HAL_RCC_USART4_RELEASE_RESET();
    
  	huart.Init.BaudRate = ulBaudRate;
  	huart.Init.Mode = UART_MODE_TX_RX;
  	huart.Init.HwFlowCtl = UART_HWCONTROL_NONE;
  	huart.Init.OverSampling = UART_OVERSAMPLING_16;
  	huart.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
  	huart.Init.ClockPrescaler = UART_PRESCALER_DIV1;
  	huart.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
    
	switch (ucPORT)
	{
		case 4 :
			__HAL_RCC_USART4_CLK_ENABLE();
    		__HAL_RCC_GPIOA_CLK_ENABLE();

			GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1;
			GPIO_InitStruct.Alternate = GPIO_AF4_USART4;
			HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

			huart.Instance = USART4;

			HAL_NVIC_SetPriority(USART3_4_IRQn, 5, 0);

			break;

		default : 
			return FALSE;
	}

	switch (eParity)
	{
		case MB_PAR_NONE :
			huart.Init.Parity = UART_PARITY_NONE;
            huart.Init.WordLength = UART_WORDLENGTH_8B;
			break;
		case MB_PAR_ODD :
			huart.Init.Parity = UART_PARITY_ODD;
            huart.Init.WordLength = UART_WORDLENGTH_9B;
			break;
		case MB_PAR_EVEN :
			huart.Init.Parity = UART_PARITY_EVEN;
            huart.Init.WordLength = UART_WORDLENGTH_9B;
			break;

		default :
			return FALSE;
	}

    switch (stop_bit)
    {
        case 1 :
            huart.Init.StopBits = UART_STOPBITS_1;
        break;
        
        case 3 :
            huart.Init.StopBits = UART_STOPBITS_2;
        break;
        
        default :
            return FALSE;
         
    }
    
	HAL_UART_Init(&huart);
	HAL_NVIC_EnableIRQ(USART3_4_IRQn);

    return TRUE;
#endif    
}

//
void vMBPortSerialClose( void )
{
    crm_periph_clock_enable(CRM_USART3_PERIPH_CLOCK, FALSE);
}

//
BOOL xMBPortSerialPutByte( CHAR ucByte )
{
#if 0  
	huart.Instance->TDR = ucByte;
	return TRUE;
#endif    
}

//
BOOL xMBPortSerialGetByte( CHAR * pucByte )
{
#if 0  
    *pucByte = huart.Instance->RDR;
    return TRUE;
#endif   
}

//
void USART3_IRQHandler(void)
{
    
}

//
void vMB_USART_IRQHandler(void)
{
#if 0  
	if ((__HAL_UART_GET_IT(&huart, UART_IT_RXNE) != RESET) && (__HAL_UART_GET_IT_SOURCE(&huart, UART_IT_RXNE) != RESET)) {
		pxMBFrameCBByteReceived();
		__HAL_UART_SEND_REQ(&huart, UART_RXDATA_FLUSH_REQUEST);
	}
	if ((__HAL_UART_GET_IT(&huart, UART_IT_TXE) != RESET) &&(__HAL_UART_GET_IT_SOURCE(&huart, UART_IT_TXE) != RESET)) {
		pxMBFrameCBTransmitterEmpty();
		HAL_GPIO_TogglePin(GPIOA, GPIO_PIN_5);
	}
    
    if (__HAL_UART_GET_IT(&huart, UART_IT_ERR) != RESET)
        __HAL_UART_CLEAR_IT(&huart, UART_CLEAR_OREF);
#endif    
}