bt-67xx_universal_hw/stm32/stm32f4xx_spl/src/stm32f4xx_can.c

/**
  ******************************************************************************
  * @file    stm32f4xx_can.c
  * @author  MCD Application Team
  * @version V1.0.2
  * @date    05-March-2012
  * @brief   This file provides firmware functions to manage the following 
  *          functionalities of the Controller area network (CAN) peripheral:           
  *           - Initialization and Configuration 
  *           - CAN Frames Transmission 
  *           - CAN Frames Reception    
  *           - Operation modes switch  
  *           - Error management          
  *           - Interrupts and flags        
  *         
  *  @verbatim
  *                               
  *          ===================================================================      
  *                                   How to use this driver
  *          ===================================================================
                
  *          1.  Enable the CAN controller interface clock using 
  *                  RCC_APB1PeriphClockCmd(RCC_APB1Periph_CAN1, ENABLE); for CAN1 
  *              and RCC_APB1PeriphClockCmd(RCC_APB1Periph_CAN2, ENABLE); for CAN2
  *  @note   In case you are using CAN2 only, you have to enable the CAN1 clock.
  *     
  *          2. CAN pins configuration
  *               - Enable the clock for the CAN GPIOs using the following function:
  *                   RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOx, ENABLE);   
  *               - Connect the involved CAN pins to AF9 using the following function 
  *                   GPIO_PinAFConfig(GPIOx, GPIO_PinSourcex, GPIO_AF_CANx); 
  *                - Configure these CAN pins in alternate function mode by calling
  *                  the function  GPIO_Init();
  *    
  *          3.  Initialise and configure the CAN using CAN_Init() and 
  *               CAN_FilterInit() functions.   
  *               
  *          4.  Transmit the desired CAN frame using CAN_Transmit() function.
  *         
  *          5.  Check the transmission of a CAN frame using CAN_TransmitStatus()
  *              function.
  *               
  *          6.  Cancel the transmission of a CAN frame using CAN_CancelTransmit()
  *              function.  
  *            
  *          7.  Receive a CAN frame using CAN_Recieve() function.
  *         
  *          8.  Release the receive FIFOs using CAN_FIFORelease() function.
  *               
  *          9. Return the number of pending received frames using 
  *              CAN_MessagePending() function.            
  *                   
  *          10. To control CAN events you can use one of the following two methods:
  *               - Check on CAN flags using the CAN_GetFlagStatus() function.  
  *               - Use CAN interrupts through the function CAN_ITConfig() at 
  *                 initialization phase and CAN_GetITStatus() function into 
  *                 interrupt routines to check if the event has occurred or not.
  *             After checking on a flag you should clear it using CAN_ClearFlag()
  *             function. And after checking on an interrupt event you should 
  *             clear it using CAN_ClearITPendingBit() function.            
  *               
  *              
  *  @endverbatim
  *         
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT 2012 STMicroelectronics</center></h2>
  *
  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
  * You may not use this file except in compliance with the License.
  * You may obtain a copy of the License at:
  *
  *        http://www.st.com/software_license_agreement_liberty_v2
  *
  * Unless required by applicable law or agreed to in writing, software 
  * distributed under the License is distributed on an "AS IS" BASIS, 
  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  * See the License for the specific language governing permissions and
  * limitations under the License.
  *
  ******************************************************************************
  */

/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_can.h"
#include "stm32f4xx_rcc.h"

/** @addtogroup STM32F4xx_StdPeriph_Driver
  * @{
  */

/** @defgroup CAN 
  * @brief CAN driver modules
  * @{
  */ 
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/

/* CAN Master Control Register bits */
#define MCR_DBF           ((uint32_t)0x00010000) /* software master reset */

/* CAN Mailbox Transmit Request */
#define TMIDxR_TXRQ       ((uint32_t)0x00000001) /* Transmit mailbox request */

/* CAN Filter Master Register bits */
#define FMR_FINIT         ((uint32_t)0x00000001) /* Filter init mode */

/* Time out for INAK bit */
#define INAK_TIMEOUT      ((uint32_t)0x0000FFFF)
/* Time out for SLAK bit */
#define SLAK_TIMEOUT      ((uint32_t)0x0000FFFF)

/* Flags in TSR register */
#define CAN_FLAGS_TSR     ((uint32_t)0x08000000) 
/* Flags in RF1R register */
#define CAN_FLAGS_RF1R    ((uint32_t)0x04000000) 
/* Flags in RF0R register */
#define CAN_FLAGS_RF0R    ((uint32_t)0x02000000) 
/* Flags in MSR register */
#define CAN_FLAGS_MSR     ((uint32_t)0x01000000) 
/* Flags in ESR register */
#define CAN_FLAGS_ESR     ((uint32_t)0x00F00000) 

/* Mailboxes definition */
#define CAN_TXMAILBOX_0   ((uint8_t)0x00)
#define CAN_TXMAILBOX_1   ((uint8_t)0x01)
#define CAN_TXMAILBOX_2   ((uint8_t)0x02) 

#define CAN_MODE_MASK     ((uint32_t) 0x00000003)

/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
static ITStatus CheckITStatus(uint32_t CAN_Reg, uint32_t It_Bit);

/** @defgroup CAN_Private_Functions
  * @{
  */

/** @defgroup CAN_Group1 Initialization and Configuration functions
 *  @brief    Initialization and Configuration functions 
 *
@verbatim    
 ===============================================================================
                      Initialization and Configuration functions
 ===============================================================================  
  This section provides functions allowing to 
   - Initialize the CAN peripherals : Prescaler, operating mode, the maximum number 
     of time quanta to perform resynchronization, the number of time quanta in
     Bit Segment 1 and 2 and many other modes. 
     Refer to  @ref CAN_InitTypeDef  for more details.
   - Configures the CAN reception filter.                                      
   - Select the start bank filter for slave CAN.
   - Enables or disables the Debug Freeze mode for CAN
   - Enables or disables the CAN Time Trigger Operation communication mode
   
@endverbatim
  * @{
  */
  
/**
  * @brief  Deinitializes the CAN peripheral registers to their default reset values.
  * @param  CANx: where x can be 1 or 2 to select the CAN peripheral.
  * @retval None.
  */
void CAN_DeInit(CAN_TypeDef* CANx)
{
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
 
  if (CANx == CAN1)
  {
    /* Enable CAN1 reset state */
    RCC_APB1PeriphResetCmd(RCC_APB1Periph_CAN1, ENABLE);
    /* Release CAN1 from reset state */
    RCC_APB1PeriphResetCmd(RCC_APB1Periph_CAN1, DISABLE);
  }
  else
  {  
    /* Enable CAN2 reset state */
    RCC_APB1PeriphResetCmd(RCC_APB1Periph_CAN2, ENABLE);
    /* Release CAN2 from reset state */
    RCC_APB1PeriphResetCmd(RCC_APB1Periph_CAN2, DISABLE);
  }
}

/**
  * @brief  Initializes the CAN peripheral according to the specified
  *         parameters in the CAN_InitStruct.
  * @param  CANx: where x can be 1 or 2 to select the CAN peripheral.
  * @param  CAN_InitStruct: pointer to a CAN_InitTypeDef structure that contains
  *         the configuration information for the CAN peripheral.
  * @retval Constant indicates initialization succeed which will be 
  *         CAN_InitStatus_Failed or CAN_InitStatus_Success.
  */
uint8_t CAN_Init(CAN_TypeDef* CANx, CAN_InitTypeDef* CAN_InitStruct)
{
  uint8_t InitStatus = CAN_InitStatus_Failed;
  uint32_t wait_ack = 0x00000000;
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_FUNCTIONAL_STATE(CAN_InitStruct->CAN_TTCM));
  assert_param(IS_FUNCTIONAL_STATE(CAN_InitStruct->CAN_ABOM));
  assert_param(IS_FUNCTIONAL_STATE(CAN_InitStruct->CAN_AWUM));
  assert_param(IS_FUNCTIONAL_STATE(CAN_InitStruct->CAN_NART));
  assert_param(IS_FUNCTIONAL_STATE(CAN_InitStruct->CAN_RFLM));
  assert_param(IS_FUNCTIONAL_STATE(CAN_InitStruct->CAN_TXFP));
  assert_param(IS_CAN_MODE(CAN_InitStruct->CAN_Mode));
  assert_param(IS_CAN_SJW(CAN_InitStruct->CAN_SJW));
  assert_param(IS_CAN_BS1(CAN_InitStruct->CAN_BS1));
  assert_param(IS_CAN_BS2(CAN_InitStruct->CAN_BS2));
  assert_param(IS_CAN_PRESCALER(CAN_InitStruct->CAN_Prescaler));

  /* Exit from sleep mode */
  CANx->MCR &= (~(uint32_t)CAN_MCR_SLEEP);

  /* Request initialisation */
  CANx->MCR |= CAN_MCR_INRQ ;

  /* Wait the acknowledge */
  while (((CANx->MSR & CAN_MSR_INAK) != CAN_MSR_INAK) && (wait_ack != INAK_TIMEOUT))
  {
    wait_ack++;
  }

  /* Check acknowledge */
  if ((CANx->MSR & CAN_MSR_INAK) != CAN_MSR_INAK)
  {
    InitStatus = CAN_InitStatus_Failed;
  }
  else 
  {
    /* Set the time triggered communication mode */
    if (CAN_InitStruct->CAN_TTCM == ENABLE)
    {
      CANx->MCR |= CAN_MCR_TTCM;
    }
    else
    {
      CANx->MCR &= ~(uint32_t)CAN_MCR_TTCM;
    }

    /* Set the automatic bus-off management */
    if (CAN_InitStruct->CAN_ABOM == ENABLE)
    {
      CANx->MCR |= CAN_MCR_ABOM;
    }
    else
    {
      CANx->MCR &= ~(uint32_t)CAN_MCR_ABOM;
    }

    /* Set the automatic wake-up mode */
    if (CAN_InitStruct->CAN_AWUM == ENABLE)
    {
      CANx->MCR |= CAN_MCR_AWUM;
    }
    else
    {
      CANx->MCR &= ~(uint32_t)CAN_MCR_AWUM;
    }

    /* Set the no automatic retransmission */
    if (CAN_InitStruct->CAN_NART == ENABLE)
    {
      CANx->MCR |= CAN_MCR_NART;
    }
    else
    {
      CANx->MCR &= ~(uint32_t)CAN_MCR_NART;
    }

    /* Set the receive FIFO locked mode */
    if (CAN_InitStruct->CAN_RFLM == ENABLE)
    {
      CANx->MCR |= CAN_MCR_RFLM;
    }
    else
    {
      CANx->MCR &= ~(uint32_t)CAN_MCR_RFLM;
    }

    /* Set the transmit FIFO priority */
    if (CAN_InitStruct->CAN_TXFP == ENABLE)
    {
      CANx->MCR |= CAN_MCR_TXFP;
    }
    else
    {
      CANx->MCR &= ~(uint32_t)CAN_MCR_TXFP;
    }

    /* Set the bit timing register */
    CANx->BTR = (uint32_t)((uint32_t)CAN_InitStruct->CAN_Mode << 30) | \
                ((uint32_t)CAN_InitStruct->CAN_SJW << 24) | \
                ((uint32_t)CAN_InitStruct->CAN_BS1 << 16) | \
                ((uint32_t)CAN_InitStruct->CAN_BS2 << 20) | \
               ((uint32_t)CAN_InitStruct->CAN_Prescaler - 1);

    /* Request leave initialisation */
    CANx->MCR &= ~(uint32_t)CAN_MCR_INRQ;

   /* Wait the acknowledge */
   wait_ack = 0;

   while (((CANx->MSR & CAN_MSR_INAK) == CAN_MSR_INAK) && (wait_ack != INAK_TIMEOUT))
   {
     wait_ack++;
   }

    /* ...and check acknowledged */
    if ((CANx->MSR & CAN_MSR_INAK) == CAN_MSR_INAK)
    {
      InitStatus = CAN_InitStatus_Failed;
    }
    else
    {
      InitStatus = CAN_InitStatus_Success ;
    }
  }

  /* At this step, return the status of initialization */
  return InitStatus;
}

/**
  * @brief  Configures the CAN reception filter according to the specified
  *         parameters in the CAN_FilterInitStruct.
  * @param  CAN_FilterInitStruct: pointer to a CAN_FilterInitTypeDef structure that
  *         contains the configuration information.
  * @retval None
  */
void CAN_FilterInit(CAN_FilterInitTypeDef* CAN_FilterInitStruct)
{
  uint32_t filter_number_bit_pos = 0;
  /* Check the parameters */
  assert_param(IS_CAN_FILTER_NUMBER(CAN_FilterInitStruct->CAN_FilterNumber));
  assert_param(IS_CAN_FILTER_MODE(CAN_FilterInitStruct->CAN_FilterMode));
  assert_param(IS_CAN_FILTER_SCALE(CAN_FilterInitStruct->CAN_FilterScale));
  assert_param(IS_CAN_FILTER_FIFO(CAN_FilterInitStruct->CAN_FilterFIFOAssignment));
  assert_param(IS_FUNCTIONAL_STATE(CAN_FilterInitStruct->CAN_FilterActivation));

  filter_number_bit_pos = ((uint32_t)1) << CAN_FilterInitStruct->CAN_FilterNumber;

  /* Initialisation mode for the filter */
  CAN1->FMR |= FMR_FINIT;

  /* Filter Deactivation */
  CAN1->FA1R &= ~(uint32_t)filter_number_bit_pos;

  /* Filter Scale */
  if (CAN_FilterInitStruct->CAN_FilterScale == CAN_FilterScale_16bit)
  {
    /* 16-bit scale for the filter */
    CAN1->FS1R &= ~(uint32_t)filter_number_bit_pos;

    /* First 16-bit identifier and First 16-bit mask */
    /* Or First 16-bit identifier and Second 16-bit identifier */
    CAN1->sFilterRegister[CAN_FilterInitStruct->CAN_FilterNumber].FR1 = 
       ((0x0000FFFF & (uint32_t)CAN_FilterInitStruct->CAN_FilterMaskIdLow) << 16) |
        (0x0000FFFF & (uint32_t)CAN_FilterInitStruct->CAN_FilterIdLow);

    /* Second 16-bit identifier and Second 16-bit mask */
    /* Or Third 16-bit identifier and Fourth 16-bit identifier */
    CAN1->sFilterRegister[CAN_FilterInitStruct->CAN_FilterNumber].FR2 = 
       ((0x0000FFFF & (uint32_t)CAN_FilterInitStruct->CAN_FilterMaskIdHigh) << 16) |
        (0x0000FFFF & (uint32_t)CAN_FilterInitStruct->CAN_FilterIdHigh);
  }

  if (CAN_FilterInitStruct->CAN_FilterScale == CAN_FilterScale_32bit)
  {
    /* 32-bit scale for the filter */
    CAN1->FS1R |= filter_number_bit_pos;
    /* 32-bit identifier or First 32-bit identifier */
    CAN1->sFilterRegister[CAN_FilterInitStruct->CAN_FilterNumber].FR1 = 
       ((0x0000FFFF & (uint32_t)CAN_FilterInitStruct->CAN_FilterIdHigh) << 16) |
        (0x0000FFFF & (uint32_t)CAN_FilterInitStruct->CAN_FilterIdLow);
    /* 32-bit mask or Second 32-bit identifier */
    CAN1->sFilterRegister[CAN_FilterInitStruct->CAN_FilterNumber].FR2 = 
       ((0x0000FFFF & (uint32_t)CAN_FilterInitStruct->CAN_FilterMaskIdHigh) << 16) |
        (0x0000FFFF & (uint32_t)CAN_FilterInitStruct->CAN_FilterMaskIdLow);
  }

  /* Filter Mode */
  if (CAN_FilterInitStruct->CAN_FilterMode == CAN_FilterMode_IdMask)
  {
    /*Id/Mask mode for the filter*/
    CAN1->FM1R &= ~(uint32_t)filter_number_bit_pos;
  }
  else /* CAN_FilterInitStruct->CAN_FilterMode == CAN_FilterMode_IdList */
  {
    /*Identifier list mode for the filter*/
    CAN1->FM1R |= (uint32_t)filter_number_bit_pos;
  }

  /* Filter FIFO assignment */
  if (CAN_FilterInitStruct->CAN_FilterFIFOAssignment == CAN_Filter_FIFO0)
  {
    /* FIFO 0 assignation for the filter */
    CAN1->FFA1R &= ~(uint32_t)filter_number_bit_pos;
  }

  if (CAN_FilterInitStruct->CAN_FilterFIFOAssignment == CAN_Filter_FIFO1)
  {
    /* FIFO 1 assignation for the filter */
    CAN1->FFA1R |= (uint32_t)filter_number_bit_pos;
  }
  
  /* Filter activation */
  if (CAN_FilterInitStruct->CAN_FilterActivation == ENABLE)
  {
    CAN1->FA1R |= filter_number_bit_pos;
  }

  /* Leave the initialisation mode for the filter */
  CAN1->FMR &= ~FMR_FINIT;
}

/**
  * @brief  Fills each CAN_InitStruct member with its default value.
  * @param  CAN_InitStruct: pointer to a CAN_InitTypeDef structure which ill be initialized.
  * @retval None
  */
void CAN_StructInit(CAN_InitTypeDef* CAN_InitStruct)
{
  /* Reset CAN init structure parameters values */
  
  /* Initialize the time triggered communication mode */
  CAN_InitStruct->CAN_TTCM = DISABLE;
  
  /* Initialize the automatic bus-off management */
  CAN_InitStruct->CAN_ABOM = DISABLE;
  
  /* Initialize the automatic wake-up mode */
  CAN_InitStruct->CAN_AWUM = DISABLE;
  
  /* Initialize the no automatic retransmission */
  CAN_InitStruct->CAN_NART = DISABLE;
  
  /* Initialize the receive FIFO locked mode */
  CAN_InitStruct->CAN_RFLM = DISABLE;
  
  /* Initialize the transmit FIFO priority */
  CAN_InitStruct->CAN_TXFP = DISABLE;
  
  /* Initialize the CAN_Mode member */
  CAN_InitStruct->CAN_Mode = CAN_Mode_Normal;
  
  /* Initialize the CAN_SJW member */
  CAN_InitStruct->CAN_SJW = CAN_SJW_1tq;
  
  /* Initialize the CAN_BS1 member */
  CAN_InitStruct->CAN_BS1 = CAN_BS1_4tq;
  
  /* Initialize the CAN_BS2 member */
  CAN_InitStruct->CAN_BS2 = CAN_BS2_3tq;
  
  /* Initialize the CAN_Prescaler member */
  CAN_InitStruct->CAN_Prescaler = 1;
}

/**
  * @brief  Select the start bank filter for slave CAN.
  * @param  CAN_BankNumber: Select the start slave bank filter from 1..27.
  * @retval None
  */
void CAN_SlaveStartBank(uint8_t CAN_BankNumber) 
{
  /* Check the parameters */
  assert_param(IS_CAN_BANKNUMBER(CAN_BankNumber));
  
  /* Enter Initialisation mode for the filter */
  CAN1->FMR |= FMR_FINIT;
  
  /* Select the start slave bank */
  CAN1->FMR &= (uint32_t)0xFFFFC0F1 ;
  CAN1->FMR |= (uint32_t)(CAN_BankNumber)<<8;
  
  /* Leave Initialisation mode for the filter */
  CAN1->FMR &= ~FMR_FINIT;
}

/**
  * @brief  Enables or disables the DBG Freeze for CAN.
  * @param  CANx: where x can be 1 or 2 to to select the CAN peripheral.
  * @param  NewState: new state of the CAN peripheral. 
  *          This parameter can be: ENABLE (CAN reception/transmission is frozen
  *          during debug. Reception FIFOs can still be accessed/controlled normally) 
  *          or DISABLE (CAN is working during debug).
  * @retval None
  */
void CAN_DBGFreeze(CAN_TypeDef* CANx, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  
  if (NewState != DISABLE)
  {
    /* Enable Debug Freeze  */
    CANx->MCR |= MCR_DBF;
  }
  else
  {
    /* Disable Debug Freeze */
    CANx->MCR &= ~MCR_DBF;
  }
}


/**
  * @brief  Enables or disables the CAN Time TriggerOperation communication mode.
  * @note   DLC must be programmed as 8 in order Time Stamp (2 bytes) to be 
  *         sent over the CAN bus.  
  * @param  CANx: where x can be 1 or 2 to to select the CAN peripheral.
  * @param  NewState: Mode new state. This parameter can be: ENABLE or DISABLE.
  *         When enabled, Time stamp (TIME[15:0]) value is  sent in the last two
  *         data bytes of the 8-byte message: TIME[7:0] in data byte 6 and TIME[15:8] 
  *         in data byte 7. 
  * @retval None
  */
void CAN_TTComModeCmd(CAN_TypeDef* CANx, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_FUNCTIONAL_STATE(NewState));
  if (NewState != DISABLE)
  {
    /* Enable the TTCM mode */
    CANx->MCR |= CAN_MCR_TTCM;

    /* Set TGT bits */
    CANx->sTxMailBox[0].TDTR |= ((uint32_t)CAN_TDT0R_TGT);
    CANx->sTxMailBox[1].TDTR |= ((uint32_t)CAN_TDT1R_TGT);
    CANx->sTxMailBox[2].TDTR |= ((uint32_t)CAN_TDT2R_TGT);
  }
  else
  {
    /* Disable the TTCM mode */
    CANx->MCR &= (uint32_t)(~(uint32_t)CAN_MCR_TTCM);

    /* Reset TGT bits */
    CANx->sTxMailBox[0].TDTR &= ((uint32_t)~CAN_TDT0R_TGT);
    CANx->sTxMailBox[1].TDTR &= ((uint32_t)~CAN_TDT1R_TGT);
    CANx->sTxMailBox[2].TDTR &= ((uint32_t)~CAN_TDT2R_TGT);
  }
}
/**
  * @}
  */


/** @defgroup CAN_Group2 CAN Frames Transmission functions
 *  @brief    CAN Frames Transmission functions 
 *
@verbatim    
 ===============================================================================
                      CAN Frames Transmission functions
 ===============================================================================  
  This section provides functions allowing to 
   - Initiate and transmit a CAN frame message (if there is an empty mailbox).
   - Check the transmission status of a CAN Frame
   - Cancel a transmit request
   
@endverbatim
  * @{
  */

/**
  * @brief  Initiates and transmits a CAN frame message.
  * @param  CANx: where x can be 1 or 2 to to select the CAN peripheral.
  * @param  TxMessage: pointer to a structure which contains CAN Id, CAN DLC and CAN data.
  * @retval The number of the mailbox that is used for transmission or
  *         CAN_TxStatus_NoMailBox if there is no empty mailbox.
  */
uint8_t CAN_Transmit(CAN_TypeDef* CANx, CanTxMsg* TxMessage)
{
  uint8_t transmit_mailbox = 0;
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_IDTYPE(TxMessage->IDE));
  assert_param(IS_CAN_RTR(TxMessage->RTR));
  assert_param(IS_CAN_DLC(TxMessage->DLC));

  /* Select one empty transmit mailbox */
  if ((CANx->TSR&CAN_TSR_TME0) == CAN_TSR_TME0)
  {
    transmit_mailbox = 0;
  }
  else if ((CANx->TSR&CAN_TSR_TME1) == CAN_TSR_TME1)
  {
    transmit_mailbox = 1;
  }
  else if ((CANx->TSR&CAN_TSR_TME2) == CAN_TSR_TME2)
  {
    transmit_mailbox = 2;
  }
  else
  {
    transmit_mailbox = CAN_TxStatus_NoMailBox;
  }

  if (transmit_mailbox != CAN_TxStatus_NoMailBox)
  {
    /* Set up the Id */
    CANx->sTxMailBox[transmit_mailbox].TIR &= TMIDxR_TXRQ;
    if (TxMessage->IDE == CAN_Id_Standard)
    {
      assert_param(IS_CAN_STDID(TxMessage->StdId));  
      CANx->sTxMailBox[transmit_mailbox].TIR |= ((TxMessage->StdId << 21) | \
                                                  TxMessage->RTR);
    }
    else
    {
      assert_param(IS_CAN_EXTID(TxMessage->ExtId));
      CANx->sTxMailBox[transmit_mailbox].TIR |= ((TxMessage->ExtId << 3) | \
                                                  TxMessage->IDE | \
                                                  TxMessage->RTR);
    }
    
    /* Set up the DLC */
    TxMessage->DLC &= (uint8_t)0x0000000F;
    CANx->sTxMailBox[transmit_mailbox].TDTR &= (uint32_t)0xFFFFFFF0;
    CANx->sTxMailBox[transmit_mailbox].TDTR |= TxMessage->DLC;

    /* Set up the data field */
    CANx->sTxMailBox[transmit_mailbox].TDLR = (((uint32_t)TxMessage->Data[3] << 24) | 
                                             ((uint32_t)TxMessage->Data[2] << 16) |
                                             ((uint32_t)TxMessage->Data[1] << 8) | 
                                             ((uint32_t)TxMessage->Data[0]));
    CANx->sTxMailBox[transmit_mailbox].TDHR = (((uint32_t)TxMessage->Data[7] << 24) | 
                                             ((uint32_t)TxMessage->Data[6] << 16) |
                                             ((uint32_t)TxMessage->Data[5] << 8) |
                                             ((uint32_t)TxMessage->Data[4]));
    /* Request transmission */
    CANx->sTxMailBox[transmit_mailbox].TIR |= TMIDxR_TXRQ;
  }
  return transmit_mailbox;
}

/**
  * @brief  Checks the transmission status of a CAN Frame.
  * @param  CANx: where x can be 1 or 2 to select the CAN peripheral.
  * @param  TransmitMailbox: the number of the mailbox that is used for transmission.
  * @retval CAN_TxStatus_Ok if the CAN driver transmits the message, 
  *         CAN_TxStatus_Failed in an other case.
  */
uint8_t CAN_TransmitStatus(CAN_TypeDef* CANx, uint8_t TransmitMailbox)
{
  uint32_t state = 0;

  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_TRANSMITMAILBOX(TransmitMailbox));
 
  switch (TransmitMailbox)
  {
    case (CAN_TXMAILBOX_0): 
      state =   CANx->TSR &  (CAN_TSR_RQCP0 | CAN_TSR_TXOK0 | CAN_TSR_TME0);
      break;
    case (CAN_TXMAILBOX_1): 
      state =   CANx->TSR &  (CAN_TSR_RQCP1 | CAN_TSR_TXOK1 | CAN_TSR_TME1);
      break;
    case (CAN_TXMAILBOX_2): 
      state =   CANx->TSR &  (CAN_TSR_RQCP2 | CAN_TSR_TXOK2 | CAN_TSR_TME2);
      break;
    default:
      state = CAN_TxStatus_Failed;
      break;
  }
  switch (state)
  {
      /* transmit pending  */
    case (0x0): state = CAN_TxStatus_Pending;
      break;
      /* transmit failed  */
     case (CAN_TSR_RQCP0 | CAN_TSR_TME0): state = CAN_TxStatus_Failed;
      break;
     case (CAN_TSR_RQCP1 | CAN_TSR_TME1): state = CAN_TxStatus_Failed;
      break;
     case (CAN_TSR_RQCP2 | CAN_TSR_TME2): state = CAN_TxStatus_Failed;
      break;
      /* transmit succeeded  */
    case (CAN_TSR_RQCP0 | CAN_TSR_TXOK0 | CAN_TSR_TME0):state = CAN_TxStatus_Ok;
      break;
    case (CAN_TSR_RQCP1 | CAN_TSR_TXOK1 | CAN_TSR_TME1):state = CAN_TxStatus_Ok;
      break;
    case (CAN_TSR_RQCP2 | CAN_TSR_TXOK2 | CAN_TSR_TME2):state = CAN_TxStatus_Ok;
      break;
    default: state = CAN_TxStatus_Failed;
      break;
  }
  return (uint8_t) state;
}

/**
  * @brief  Cancels a transmit request.
  * @param  CANx: where x can be 1 or 2 to select the CAN peripheral.
  * @param  Mailbox: Mailbox number.
  * @retval None
  */
void CAN_CancelTransmit(CAN_TypeDef* CANx, uint8_t Mailbox)
{
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_TRANSMITMAILBOX(Mailbox));
  /* abort transmission */
  switch (Mailbox)
  {
    case (CAN_TXMAILBOX_0): CANx->TSR |= CAN_TSR_ABRQ0;
      break;
    case (CAN_TXMAILBOX_1): CANx->TSR |= CAN_TSR_ABRQ1;
      break;
    case (CAN_TXMAILBOX_2): CANx->TSR |= CAN_TSR_ABRQ2;
      break;
    default:
      break;
  }
}
/**
  * @}
  */


/** @defgroup CAN_Group3 CAN Frames Reception functions
 *  @brief    CAN Frames Reception functions 
 *
@verbatim    
 ===============================================================================
                      CAN Frames Reception functions
 ===============================================================================  
  This section provides functions allowing to 
   -  Receive a correct CAN frame
   -  Release a specified receive FIFO (2 FIFOs are available)
   -  Return the number of the pending received CAN frames
   
@endverbatim
  * @{
  */

/**
  * @brief  Receives a correct CAN frame.
  * @param  CANx: where x can be 1 or 2 to select the CAN peripheral.
  * @param  FIFONumber: Receive FIFO number, CAN_FIFO0 or CAN_FIFO1.
  * @param  RxMessage: pointer to a structure receive frame which contains CAN Id,
  *         CAN DLC, CAN data and FMI number.
  * @retval None
  */
void CAN_Receive(CAN_TypeDef* CANx, uint8_t FIFONumber, CanRxMsg* RxMessage)
{
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_FIFO(FIFONumber));
  /* Get the Id */
  RxMessage->IDE = (uint8_t)0x04 & CANx->sFIFOMailBox[FIFONumber].RIR;
  if (RxMessage->IDE == CAN_Id_Standard)
  {
    RxMessage->StdId = (uint32_t)0x000007FF & (CANx->sFIFOMailBox[FIFONumber].RIR >> 21);
  }
  else
  {
    RxMessage->ExtId = (uint32_t)0x1FFFFFFF & (CANx->sFIFOMailBox[FIFONumber].RIR >> 3);
  }
  
  RxMessage->RTR = (uint8_t)0x02 & CANx->sFIFOMailBox[FIFONumber].RIR;
  /* Get the DLC */
  RxMessage->DLC = (uint8_t)0x0F & CANx->sFIFOMailBox[FIFONumber].RDTR;
  /* Get the FMI */
  RxMessage->FMI = (uint8_t)0xFF & (CANx->sFIFOMailBox[FIFONumber].RDTR >> 8);
  /* Get the data field */
  RxMessage->Data[0] = (uint8_t)0xFF & CANx->sFIFOMailBox[FIFONumber].RDLR;
  RxMessage->Data[1] = (uint8_t)0xFF & (CANx->sFIFOMailBox[FIFONumber].RDLR >> 8);
  RxMessage->Data[2] = (uint8_t)0xFF & (CANx->sFIFOMailBox[FIFONumber].RDLR >> 16);
  RxMessage->Data[3] = (uint8_t)0xFF & (CANx->sFIFOMailBox[FIFONumber].RDLR >> 24);
  RxMessage->Data[4] = (uint8_t)0xFF & CANx->sFIFOMailBox[FIFONumber].RDHR;
  RxMessage->Data[5] = (uint8_t)0xFF & (CANx->sFIFOMailBox[FIFONumber].RDHR >> 8);
  RxMessage->Data[6] = (uint8_t)0xFF & (CANx->sFIFOMailBox[FIFONumber].RDHR >> 16);
  RxMessage->Data[7] = (uint8_t)0xFF & (CANx->sFIFOMailBox[FIFONumber].RDHR >> 24);
  /* Release the FIFO */
  /* Release FIFO0 */
  if (FIFONumber == CAN_FIFO0)
  {
    CANx->RF0R |= CAN_RF0R_RFOM0;
  }
  /* Release FIFO1 */
  else /* FIFONumber == CAN_FIFO1 */
  {
    CANx->RF1R |= CAN_RF1R_RFOM1;
  }
}

/**
  * @brief  Releases the specified receive FIFO.
  * @param  CANx: where x can be 1 or 2 to select the CAN peripheral.
  * @param  FIFONumber: FIFO to release, CAN_FIFO0 or CAN_FIFO1.
  * @retval None
  */
void CAN_FIFORelease(CAN_TypeDef* CANx, uint8_t FIFONumber)
{
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_FIFO(FIFONumber));
  /* Release FIFO0 */
  if (FIFONumber == CAN_FIFO0)
  {
    CANx->RF0R |= CAN_RF0R_RFOM0;
  }
  /* Release FIFO1 */
  else /* FIFONumber == CAN_FIFO1 */
  {
    CANx->RF1R |= CAN_RF1R_RFOM1;
  }
}

/**
  * @brief  Returns the number of pending received messages.
  * @param  CANx: where x can be 1 or 2 to select the CAN peripheral.
  * @param  FIFONumber: Receive FIFO number, CAN_FIFO0 or CAN_FIFO1.
  * @retval NbMessage : which is the number of pending message.
  */
uint8_t CAN_MessagePending(CAN_TypeDef* CANx, uint8_t FIFONumber)
{
  uint8_t message_pending=0;
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_FIFO(FIFONumber));
  if (FIFONumber == CAN_FIFO0)
  {
    message_pending = (uint8_t)(CANx->RF0R&(uint32_t)0x03);
  }
  else if (FIFONumber == CAN_FIFO1)
  {
    message_pending = (uint8_t)(CANx->RF1R&(uint32_t)0x03);
  }
  else
  {
    message_pending = 0;
  }
  return message_pending;
}
/**
  * @}
  */


/** @defgroup CAN_Group4 CAN Operation modes functions
 *  @brief    CAN Operation modes functions 
 *
@verbatim    
 ===============================================================================
                      CAN Operation modes functions
 ===============================================================================  
  This section provides functions allowing to select the CAN Operation modes
  - sleep mode
  - normal mode 
  - initialization mode
   
@endverbatim
  * @{
  */
  
  
/**
  * @brief  Selects the CAN Operation mode.
  * @param  CAN_OperatingMode: CAN Operating Mode.
  *         This parameter can be one of @ref CAN_OperatingMode_TypeDef enumeration.
  * @retval status of the requested mode which can be 
  *         - CAN_ModeStatus_Failed:  CAN failed entering the specific mode 
  *         - CAN_ModeStatus_Success: CAN Succeed entering the specific mode 
  */
uint8_t CAN_OperatingModeRequest(CAN_TypeDef* CANx, uint8_t CAN_OperatingMode)
{
  uint8_t status = CAN_ModeStatus_Failed;
  
  /* Timeout for INAK or also for SLAK bits*/
  uint32_t timeout = INAK_TIMEOUT; 

  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_OPERATING_MODE(CAN_OperatingMode));

  if (CAN_OperatingMode == CAN_OperatingMode_Initialization)
  {
    /* Request initialisation */
    CANx->MCR = (uint32_t)((CANx->MCR & (uint32_t)(~(uint32_t)CAN_MCR_SLEEP)) | CAN_MCR_INRQ);

    /* Wait the acknowledge */
    while (((CANx->MSR & CAN_MODE_MASK) != CAN_MSR_INAK) && (timeout != 0))
    {
      timeout--;
    }
    if ((CANx->MSR & CAN_MODE_MASK) != CAN_MSR_INAK)
    {
      status = CAN_ModeStatus_Failed;
    }
    else
    {
      status = CAN_ModeStatus_Success;
    }
  }
  else  if (CAN_OperatingMode == CAN_OperatingMode_Normal)
  {
    /* Request leave initialisation and sleep mode  and enter Normal mode */
    CANx->MCR &= (uint32_t)(~(CAN_MCR_SLEEP|CAN_MCR_INRQ));

    /* Wait the acknowledge */
    while (((CANx->MSR & CAN_MODE_MASK) != 0) && (timeout!=0))
    {
      timeout--;
    }
    if ((CANx->MSR & CAN_MODE_MASK) != 0)
    {
      status = CAN_ModeStatus_Failed;
    }
    else
    {
      status = CAN_ModeStatus_Success;
    }
  }
  else  if (CAN_OperatingMode == CAN_OperatingMode_Sleep)
  {
    /* Request Sleep mode */
    CANx->MCR = (uint32_t)((CANx->MCR & (uint32_t)(~(uint32_t)CAN_MCR_INRQ)) | CAN_MCR_SLEEP);

    /* Wait the acknowledge */
    while (((CANx->MSR & CAN_MODE_MASK) != CAN_MSR_SLAK) && (timeout!=0))
    {
      timeout--;
    }
    if ((CANx->MSR & CAN_MODE_MASK) != CAN_MSR_SLAK)
    {
      status = CAN_ModeStatus_Failed;
    }
    else
    {
      status = CAN_ModeStatus_Success;
    }
  }
  else
  {
    status = CAN_ModeStatus_Failed;
  }

  return  (uint8_t) status;
}

/**
  * @brief  Enters the Sleep (low power) mode.
  * @param  CANx: where x can be 1 or 2 to select the CAN peripheral.
  * @retval CAN_Sleep_Ok if sleep entered, CAN_Sleep_Failed otherwise.
  */
uint8_t CAN_Sleep(CAN_TypeDef* CANx)
{
  uint8_t sleepstatus = CAN_Sleep_Failed;
  
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
    
  /* Request Sleep mode */
   CANx->MCR = (((CANx->MCR) & (uint32_t)(~(uint32_t)CAN_MCR_INRQ)) | CAN_MCR_SLEEP);
   
  /* Sleep mode status */
  if ((CANx->MSR & (CAN_MSR_SLAK|CAN_MSR_INAK)) == CAN_MSR_SLAK)
  {
    /* Sleep mode not entered */
    sleepstatus =  CAN_Sleep_Ok;
  }
  /* return sleep mode status */
   return (uint8_t)sleepstatus;
}

/**
  * @brief  Wakes up the CAN peripheral from sleep mode .
  * @param  CANx: where x can be 1 or 2 to select the CAN peripheral.
  * @retval CAN_WakeUp_Ok if sleep mode left, CAN_WakeUp_Failed otherwise.
  */
uint8_t CAN_WakeUp(CAN_TypeDef* CANx)
{
  uint32_t wait_slak = SLAK_TIMEOUT;
  uint8_t wakeupstatus = CAN_WakeUp_Failed;
  
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
    
  /* Wake up request */
  CANx->MCR &= ~(uint32_t)CAN_MCR_SLEEP;
    
  /* Sleep mode status */
  while(((CANx->MSR & CAN_MSR_SLAK) == CAN_MSR_SLAK)&&(wait_slak!=0x00))
  {
   wait_slak--;
  }
  if((CANx->MSR & CAN_MSR_SLAK) != CAN_MSR_SLAK)
  {
   /* wake up done : Sleep mode exited */
    wakeupstatus = CAN_WakeUp_Ok;
  }
  /* return wakeup status */
  return (uint8_t)wakeupstatus;
}
/**
  * @}
  */


/** @defgroup CAN_Group5 CAN Bus Error management functions
 *  @brief    CAN Bus Error management functions 
 *
@verbatim    
 ===============================================================================
                      CAN Bus Error management functions
 ===============================================================================  
  This section provides functions allowing to 
   -  Return the CANx's last error code (LEC)
   -  Return the CANx Receive Error Counter (REC)
   -  Return the LSB of the 9-bit CANx Transmit Error Counter(TEC).
   
   @note If TEC is greater than 255, The CAN is in bus-off state.
   @note if REC or TEC are greater than 96, an Error warning flag occurs.
   @note if REC or TEC are greater than 127, an Error Passive Flag occurs.
                        
@endverbatim
  * @{
  */
  
/**
  * @brief  Returns the CANx's last error code (LEC).
  * @param  CANx: where x can be 1 or 2 to select the CAN peripheral.
  * @retval Error code: 
  *          - CAN_ERRORCODE_NoErr: No Error  
  *          - CAN_ERRORCODE_StuffErr: Stuff Error
  *          - CAN_ERRORCODE_FormErr: Form Error
  *          - CAN_ERRORCODE_ACKErr : Acknowledgment Error
  *          - CAN_ERRORCODE_BitRecessiveErr: Bit Recessive Error
  *          - CAN_ERRORCODE_BitDominantErr: Bit Dominant Error
  *          - CAN_ERRORCODE_CRCErr: CRC Error
  *          - CAN_ERRORCODE_SoftwareSetErr: Software Set Error  
  */
uint8_t CAN_GetLastErrorCode(CAN_TypeDef* CANx)
{
  uint8_t errorcode=0;
  
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  
  /* Get the error code*/
  errorcode = (((uint8_t)CANx->ESR) & (uint8_t)CAN_ESR_LEC);
  
  /* Return the error code*/
  return errorcode;
}

/**
  * @brief  Returns the CANx Receive Error Counter (REC).
  * @note   In case of an error during reception, this counter is incremented 
  *         by 1 or by 8 depending on the error condition as defined by the CAN 
  *         standard. After every successful reception, the counter is 
  *         decremented by 1 or reset to 120 if its value was higher than 128. 
  *         When the counter value exceeds 127, the CAN controller enters the 
  *         error passive state.  
  * @param  CANx: where x can be 1 or 2 to to select the CAN peripheral.  
  * @retval CAN Receive Error Counter. 
  */
uint8_t CAN_GetReceiveErrorCounter(CAN_TypeDef* CANx)
{
  uint8_t counter=0;
  
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  
  /* Get the Receive Error Counter*/
  counter = (uint8_t)((CANx->ESR & CAN_ESR_REC)>> 24);
  
  /* Return the Receive Error Counter*/
  return counter;
}


/**
  * @brief  Returns the LSB of the 9-bit CANx Transmit Error Counter(TEC).
  * @param  CANx: where x can be 1 or 2 to to select the CAN peripheral.
  * @retval LSB of the 9-bit CAN Transmit Error Counter. 
  */
uint8_t CAN_GetLSBTransmitErrorCounter(CAN_TypeDef* CANx)
{
  uint8_t counter=0;
  
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  
  /* Get the LSB of the 9-bit CANx Transmit Error Counter(TEC) */
  counter = (uint8_t)((CANx->ESR & CAN_ESR_TEC)>> 16);
  
  /* Return the LSB of the 9-bit CANx Transmit Error Counter(TEC) */
  return counter;
}
/**
  * @}
  */

/** @defgroup CAN_Group6 Interrupts and flags management functions
 *  @brief   Interrupts and flags management functions
 *
@verbatim   
 ===============================================================================
                   Interrupts and flags management functions
 ===============================================================================  

  This section provides functions allowing to configure the CAN Interrupts and 
  to get the status and clear flags and Interrupts pending bits.
  
  The CAN provides 14 Interrupts sources and 15 Flags:

  ===============  
      Flags :
  ===============
  The 15 flags can be divided on 4 groups: 

   A. Transmit Flags
  -----------------------
        CAN_FLAG_RQCP0, 
        CAN_FLAG_RQCP1, 
        CAN_FLAG_RQCP2  : Request completed MailBoxes 0, 1 and 2  Flags
                          Set when when the last request (transmit or abort) has 
                          been performed. 

  B. Receive Flags
  -----------------------

        CAN_FLAG_FMP0,
        CAN_FLAG_FMP1   : FIFO 0 and 1 Message Pending Flags 
                          set to signal that messages are pending in the receive 
                          FIFO.
                          These Flags are cleared only by hardware. 

        CAN_FLAG_FF0,
        CAN_FLAG_FF1    : FIFO 0 and 1 Full Flags
                          set when three messages are stored in the selected 
                          FIFO.                        

        CAN_FLAG_FOV0              
        CAN_FLAG_FOV1   : FIFO 0 and 1 Overrun Flags
                          set when a new message has been received and passed 
                          the filter while the FIFO was full.         

  C. Operating Mode Flags
  ----------------------- 
        CAN_FLAG_WKU    : Wake up Flag
                          set to signal that a SOF bit has been detected while 
                          the CAN hardware was in Sleep mode. 
        
        CAN_FLAG_SLAK   : Sleep acknowledge Flag
                          Set to signal that the CAN has entered Sleep Mode. 
    
  D. Error Flags
  ----------------------- 
        CAN_FLAG_EWG    : Error Warning Flag
                          Set when the warning limit has been reached (Receive 
                          Error Counter or Transmit Error Counter greater than 96). 
                          This Flag is cleared only by hardware.
                            
        CAN_FLAG_EPV    : Error Passive Flag
                          Set when the Error Passive limit has been reached 
                          (Receive Error Counter or Transmit Error Counter 
                          greater than 127).
                          This Flag is cleared only by hardware.
                             
        CAN_FLAG_BOF    : Bus-Off Flag
                          set when CAN enters the bus-off state. The bus-off 
                          state is entered on TEC overflow, greater than 255.
                          This Flag is cleared only by hardware.
                                   
        CAN_FLAG_LEC    : Last error code Flag
                          set If a message has been transferred (reception or
                          transmission) with error, and the error code is hold.              
                          
  ===============  
   Interrupts :
  ===============
  The 14 interrupts can be divided on 4 groups: 
  
   A. Transmit interrupt
  -----------------------   
          CAN_IT_TME   :  Transmit mailbox empty Interrupt
                          if enabled, this interrupt source is pending when 
                          no transmit request are pending for Tx mailboxes.      

   B. Receive Interrupts
  -----------------------          
        CAN_IT_FMP0,
        CAN_IT_FMP1    :  FIFO 0 and FIFO1 message pending Interrupts
                          if enabled, these interrupt sources are pending when 
                          messages are pending in the receive FIFO.
                          The corresponding interrupt pending bits are cleared 
                          only by hardware.
                
        CAN_IT_FF0,              
        CAN_IT_FF1     :  FIFO 0 and FIFO1 full Interrupts
                          if enabled, these interrupt sources are pending when
                          three messages are stored in the selected FIFO.
        
        CAN_IT_FOV0,        
        CAN_IT_FOV1    :  FIFO 0 and FIFO1 overrun Interrupts        
                          if enabled, these interrupt sources are pending when
                          a new message has been received and passed the filter
                          while the FIFO was full.

   C. Operating Mode Interrupts
  -------------------------------          
        CAN_IT_WKU     :  Wake-up Interrupt
                          if enabled, this interrupt source is pending when 
                          a SOF bit has been detected while the CAN hardware was 
                          in Sleep mode.
                                  
        CAN_IT_SLK     :  Sleep acknowledge Interrupt
                          if enabled, this interrupt source is pending when 
                          the CAN has entered Sleep Mode.       

   D. Error Interrupts 
  -----------------------         
        CAN_IT_EWG     :  Error warning Interrupt 
                          if enabled, this interrupt source is pending when
                          the warning limit has been reached (Receive Error 
                          Counter or Transmit Error Counter=96). 
                               
        CAN_IT_EPV     :  Error passive Interrupt        
                          if enabled, this interrupt source is pending when
                          the Error Passive limit has been reached (Receive 
                          Error Counter or Transmit Error Counter>127).
                          
        CAN_IT_BOF     :  Bus-off Interrupt
                          if enabled, this interrupt source is pending when
                          CAN enters the bus-off state. The bus-off state is 
                          entered on TEC overflow, greater than 255.
                          This Flag is cleared only by hardware.
                                  
        CAN_IT_LEC     :  Last error code Interrupt        
                          if enabled, this interrupt source is pending  when
                          a message has been transferred (reception or
                          transmission) with error, and the error code is hold.
                          
        CAN_IT_ERR     :  Error Interrupt
                          if enabled, this interrupt source is pending when 
                          an error condition is pending.      
                      

  Managing the CAN controller events :
  ------------------------------------ 
  The user should identify which mode will be used in his application to manage 
  the CAN controller events: Polling mode or Interrupt mode.
  
  1.  In the Polling Mode it is advised to use the following functions:
      - CAN_GetFlagStatus() : to check if flags events occur. 
      - CAN_ClearFlag()     : to clear the flags events.
  

  
  2.  In the Interrupt Mode it is advised to use the following functions:
      - CAN_ITConfig()       : to enable or disable the interrupt source.
      - CAN_GetITStatus()    : to check if Interrupt occurs.
      - CAN_ClearITPendingBit() : to clear the Interrupt pending Bit (corresponding Flag).
      @note  This function has no impact on CAN_IT_FMP0 and CAN_IT_FMP1 Interrupts 
             pending bits since there are cleared only by hardware. 
  
@endverbatim
  * @{
  */ 
/**
  * @brief  Enables or disables the specified CANx interrupts.
  * @param  CANx: where x can be 1 or 2 to to select the CAN peripheral.
  * @param  CAN_IT: specifies the CAN interrupt sources to be enabled or disabled.
  *          This parameter can be: 
  *            @arg CAN_IT_TME: Transmit mailbox empty Interrupt 
  *            @arg CAN_IT_FMP0: FIFO 0 message pending Interrupt 
  *            @arg CAN_IT_FF0: FIFO 0 full Interrupt
  *            @arg CAN_IT_FOV0: FIFO 0 overrun Interrupt
  *            @arg CAN_IT_FMP1: FIFO 1 message pending Interrupt 
  *            @arg CAN_IT_FF1: FIFO 1 full Interrupt
  *            @arg CAN_IT_FOV1: FIFO 1 overrun Interrupt
  *            @arg CAN_IT_WKU: Wake-up Interrupt
  *            @arg CAN_IT_SLK: Sleep acknowledge Interrupt  
  *            @arg CAN_IT_EWG: Error warning Interrupt
  *            @arg CAN_IT_EPV: Error passive Interrupt
  *            @arg CAN_IT_BOF: Bus-off Interrupt  
  *            @arg CAN_IT_LEC: Last error code Interrupt
  *            @arg CAN_IT_ERR: Error Interrupt
  * @param  NewState: new state of the CAN interrupts.
  *          This parameter can be: ENABLE or DISABLE.
  * @retval None
  */
void CAN_ITConfig(CAN_TypeDef* CANx, uint32_t CAN_IT, FunctionalState NewState)
{
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_IT(CAN_IT));
  assert_param(IS_FUNCTIONAL_STATE(NewState));

  if (NewState != DISABLE)
  {
    /* Enable the selected CANx interrupt */
    CANx->IER |= CAN_IT;
  }
  else
  {
    /* Disable the selected CANx interrupt */
    CANx->IER &= ~CAN_IT;
  }
}
/**
  * @brief  Checks whether the specified CAN flag is set or not.
  * @param  CANx: where x can be 1 or 2 to to select the CAN peripheral.
  * @param  CAN_FLAG: specifies the flag to check.
  *          This parameter can be one of the following values:
  *            @arg CAN_FLAG_RQCP0: Request MailBox0 Flag
  *            @arg CAN_FLAG_RQCP1: Request MailBox1 Flag
  *            @arg CAN_FLAG_RQCP2: Request MailBox2 Flag
  *            @arg CAN_FLAG_FMP0: FIFO 0 Message Pending Flag   
  *            @arg CAN_FLAG_FF0: FIFO 0 Full Flag       
  *            @arg CAN_FLAG_FOV0: FIFO 0 Overrun Flag 
  *            @arg CAN_FLAG_FMP1: FIFO 1 Message Pending Flag   
  *            @arg CAN_FLAG_FF1: FIFO 1 Full Flag        
  *            @arg CAN_FLAG_FOV1: FIFO 1 Overrun Flag     
  *            @arg CAN_FLAG_WKU: Wake up Flag
  *            @arg CAN_FLAG_SLAK: Sleep acknowledge Flag 
  *            @arg CAN_FLAG_EWG: Error Warning Flag
  *            @arg CAN_FLAG_EPV: Error Passive Flag  
  *            @arg CAN_FLAG_BOF: Bus-Off Flag    
  *            @arg CAN_FLAG_LEC: Last error code Flag      
  * @retval The new state of CAN_FLAG (SET or RESET).
  */
FlagStatus CAN_GetFlagStatus(CAN_TypeDef* CANx, uint32_t CAN_FLAG)
{
  FlagStatus bitstatus = RESET;
  
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_GET_FLAG(CAN_FLAG));
  

  if((CAN_FLAG & CAN_FLAGS_ESR) != (uint32_t)RESET)
  { 
    /* Check the status of the specified CAN flag */
    if ((CANx->ESR & (CAN_FLAG & 0x000FFFFF)) != (uint32_t)RESET)
    { 
      /* CAN_FLAG is set */
      bitstatus = SET;
    }
    else
    { 
      /* CAN_FLAG is reset */
      bitstatus = RESET;
    }
  }
  else if((CAN_FLAG & CAN_FLAGS_MSR) != (uint32_t)RESET)
  { 
    /* Check the status of the specified CAN flag */
    if ((CANx->MSR & (CAN_FLAG & 0x000FFFFF)) != (uint32_t)RESET)
    { 
      /* CAN_FLAG is set */
      bitstatus = SET;
    }
    else
    { 
      /* CAN_FLAG is reset */
      bitstatus = RESET;
    }
  }
  else if((CAN_FLAG & CAN_FLAGS_TSR) != (uint32_t)RESET)
  { 
    /* Check the status of the specified CAN flag */
    if ((CANx->TSR & (CAN_FLAG & 0x000FFFFF)) != (uint32_t)RESET)
    { 
      /* CAN_FLAG is set */
      bitstatus = SET;
    }
    else
    { 
      /* CAN_FLAG is reset */
      bitstatus = RESET;
    }
  }
  else if((CAN_FLAG & CAN_FLAGS_RF0R) != (uint32_t)RESET)
  { 
    /* Check the status of the specified CAN flag */
    if ((CANx->RF0R & (CAN_FLAG & 0x000FFFFF)) != (uint32_t)RESET)
    { 
      /* CAN_FLAG is set */
      bitstatus = SET;
    }
    else
    { 
      /* CAN_FLAG is reset */
      bitstatus = RESET;
    }
  }
  else /* If(CAN_FLAG & CAN_FLAGS_RF1R != (uint32_t)RESET) */
  { 
    /* Check the status of the specified CAN flag */
    if ((uint32_t)(CANx->RF1R & (CAN_FLAG & 0x000FFFFF)) != (uint32_t)RESET)
    { 
      /* CAN_FLAG is set */
      bitstatus = SET;
    }
    else
    { 
      /* CAN_FLAG is reset */
      bitstatus = RESET;
    }
  }
  /* Return the CAN_FLAG status */
  return  bitstatus;
}

/**
  * @brief  Clears the CAN's pending flags.
  * @param  CANx: where x can be 1 or 2 to to select the CAN peripheral.
  * @param  CAN_FLAG: specifies the flag to clear.
  *          This parameter can be one of the following values:
  *            @arg CAN_FLAG_RQCP0: Request MailBox0 Flag
  *            @arg CAN_FLAG_RQCP1: Request MailBox1 Flag
  *            @arg CAN_FLAG_RQCP2: Request MailBox2 Flag 
  *            @arg CAN_FLAG_FF0: FIFO 0 Full Flag       
  *            @arg CAN_FLAG_FOV0: FIFO 0 Overrun Flag  
  *            @arg CAN_FLAG_FF1: FIFO 1 Full Flag        
  *            @arg CAN_FLAG_FOV1: FIFO 1 Overrun Flag     
  *            @arg CAN_FLAG_WKU: Wake up Flag
  *            @arg CAN_FLAG_SLAK: Sleep acknowledge Flag    
  *            @arg CAN_FLAG_LEC: Last error code Flag        
  * @retval None
  */
void CAN_ClearFlag(CAN_TypeDef* CANx, uint32_t CAN_FLAG)
{
  uint32_t flagtmp=0;
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_CLEAR_FLAG(CAN_FLAG));
  
  if (CAN_FLAG == CAN_FLAG_LEC) /* ESR register */
  {
    /* Clear the selected CAN flags */
    CANx->ESR = (uint32_t)RESET;
  }
  else /* MSR or TSR or RF0R or RF1R */
  {
    flagtmp = CAN_FLAG & 0x000FFFFF;

    if ((CAN_FLAG & CAN_FLAGS_RF0R)!=(uint32_t)RESET)
    {
      /* Receive Flags */
      CANx->RF0R = (uint32_t)(flagtmp);
    }
    else if ((CAN_FLAG & CAN_FLAGS_RF1R)!=(uint32_t)RESET)
    {
      /* Receive Flags */
      CANx->RF1R = (uint32_t)(flagtmp);
    }
    else if ((CAN_FLAG & CAN_FLAGS_TSR)!=(uint32_t)RESET)
    {
      /* Transmit Flags */
      CANx->TSR = (uint32_t)(flagtmp);
    }
    else /* If((CAN_FLAG & CAN_FLAGS_MSR)!=(uint32_t)RESET) */
    {
      /* Operating mode Flags */
      CANx->MSR = (uint32_t)(flagtmp);
    }
  }
}

/**
  * @brief  Checks whether the specified CANx interrupt has occurred or not.
  * @param  CANx: where x can be 1 or 2 to to select the CAN peripheral.
  * @param  CAN_IT: specifies the CAN interrupt source to check.
  *          This parameter can be one of the following values:
  *            @arg CAN_IT_TME: Transmit mailbox empty Interrupt 
  *            @arg CAN_IT_FMP0: FIFO 0 message pending Interrupt 
  *            @arg CAN_IT_FF0: FIFO 0 full Interrupt
  *            @arg CAN_IT_FOV0: FIFO 0 overrun Interrupt
  *            @arg CAN_IT_FMP1: FIFO 1 message pending Interrupt 
  *            @arg CAN_IT_FF1: FIFO 1 full Interrupt
  *            @arg CAN_IT_FOV1: FIFO 1 overrun Interrupt
  *            @arg CAN_IT_WKU: Wake-up Interrupt
  *            @arg CAN_IT_SLK: Sleep acknowledge Interrupt  
  *            @arg CAN_IT_EWG: Error warning Interrupt
  *            @arg CAN_IT_EPV: Error passive Interrupt
  *            @arg CAN_IT_BOF: Bus-off Interrupt  
  *            @arg CAN_IT_LEC: Last error code Interrupt
  *            @arg CAN_IT_ERR: Error Interrupt
  * @retval The current state of CAN_IT (SET or RESET).
  */
ITStatus CAN_GetITStatus(CAN_TypeDef* CANx, uint32_t CAN_IT)
{
  ITStatus itstatus = RESET;
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_IT(CAN_IT));
  
  /* check the interrupt enable bit */
 if((CANx->IER & CAN_IT) != RESET)
 {
   /* in case the Interrupt is enabled, .... */
    switch (CAN_IT)
    {
      case CAN_IT_TME:
        /* Check CAN_TSR_RQCPx bits */
        itstatus = CheckITStatus(CANx->TSR, CAN_TSR_RQCP0|CAN_TSR_RQCP1|CAN_TSR_RQCP2);  
        break;
      case CAN_IT_FMP0:
        /* Check CAN_RF0R_FMP0 bit */
        itstatus = CheckITStatus(CANx->RF0R, CAN_RF0R_FMP0);  
        break;
      case CAN_IT_FF0:
        /* Check CAN_RF0R_FULL0 bit */
        itstatus = CheckITStatus(CANx->RF0R, CAN_RF0R_FULL0);  
        break;
      case CAN_IT_FOV0:
        /* Check CAN_RF0R_FOVR0 bit */
        itstatus = CheckITStatus(CANx->RF0R, CAN_RF0R_FOVR0);  
        break;
      case CAN_IT_FMP1:
        /* Check CAN_RF1R_FMP1 bit */
        itstatus = CheckITStatus(CANx->RF1R, CAN_RF1R_FMP1);  
        break;
      case CAN_IT_FF1:
        /* Check CAN_RF1R_FULL1 bit */
        itstatus = CheckITStatus(CANx->RF1R, CAN_RF1R_FULL1);  
        break;
      case CAN_IT_FOV1:
        /* Check CAN_RF1R_FOVR1 bit */
        itstatus = CheckITStatus(CANx->RF1R, CAN_RF1R_FOVR1);  
        break;
      case CAN_IT_WKU:
        /* Check CAN_MSR_WKUI bit */
        itstatus = CheckITStatus(CANx->MSR, CAN_MSR_WKUI);  
        break;
      case CAN_IT_SLK:
        /* Check CAN_MSR_SLAKI bit */
        itstatus = CheckITStatus(CANx->MSR, CAN_MSR_SLAKI);  
        break;
      case CAN_IT_EWG:
        /* Check CAN_ESR_EWGF bit */
        itstatus = CheckITStatus(CANx->ESR, CAN_ESR_EWGF);  
        break;
      case CAN_IT_EPV:
        /* Check CAN_ESR_EPVF bit */
        itstatus = CheckITStatus(CANx->ESR, CAN_ESR_EPVF);  
        break;
      case CAN_IT_BOF:
        /* Check CAN_ESR_BOFF bit */
        itstatus = CheckITStatus(CANx->ESR, CAN_ESR_BOFF);  
        break;
      case CAN_IT_LEC:
        /* Check CAN_ESR_LEC bit */
        itstatus = CheckITStatus(CANx->ESR, CAN_ESR_LEC);  
        break;
      case CAN_IT_ERR:
        /* Check CAN_MSR_ERRI bit */ 
        itstatus = CheckITStatus(CANx->MSR, CAN_MSR_ERRI); 
        break;
      default:
        /* in case of error, return RESET */
        itstatus = RESET;
        break;
    }
  }
  else
  {
   /* in case the Interrupt is not enabled, return RESET */
    itstatus  = RESET;
  }
  
  /* Return the CAN_IT status */
  return  itstatus;
}

/**
  * @brief  Clears the CANx's interrupt pending bits.
  * @param  CANx: where x can be 1 or 2 to to select the CAN peripheral.
  * @param  CAN_IT: specifies the interrupt pending bit to clear.
  *          This parameter can be one of the following values:
  *            @arg CAN_IT_TME: Transmit mailbox empty Interrupt
  *            @arg CAN_IT_FF0: FIFO 0 full Interrupt
  *            @arg CAN_IT_FOV0: FIFO 0 overrun Interrupt
  *            @arg CAN_IT_FF1: FIFO 1 full Interrupt
  *            @arg CAN_IT_FOV1: FIFO 1 overrun Interrupt
  *            @arg CAN_IT_WKU: Wake-up Interrupt
  *            @arg CAN_IT_SLK: Sleep acknowledge Interrupt  
  *            @arg CAN_IT_EWG: Error warning Interrupt
  *            @arg CAN_IT_EPV: Error passive Interrupt
  *            @arg CAN_IT_BOF: Bus-off Interrupt  
  *            @arg CAN_IT_LEC: Last error code Interrupt
  *            @arg CAN_IT_ERR: Error Interrupt 
  * @retval None
  */
void CAN_ClearITPendingBit(CAN_TypeDef* CANx, uint32_t CAN_IT)
{
  /* Check the parameters */
  assert_param(IS_CAN_ALL_PERIPH(CANx));
  assert_param(IS_CAN_CLEAR_IT(CAN_IT));

  switch (CAN_IT)
  {
    case CAN_IT_TME:
      /* Clear CAN_TSR_RQCPx (rc_w1)*/
      CANx->TSR = CAN_TSR_RQCP0|CAN_TSR_RQCP1|CAN_TSR_RQCP2;  
      break;
    case CAN_IT_FF0:
      /* Clear CAN_RF0R_FULL0 (rc_w1)*/
      CANx->RF0R = CAN_RF0R_FULL0; 
      break;
    case CAN_IT_FOV0:
      /* Clear CAN_RF0R_FOVR0 (rc_w1)*/
      CANx->RF0R = CAN_RF0R_FOVR0; 
      break;
    case CAN_IT_FF1:
      /* Clear CAN_RF1R_FULL1 (rc_w1)*/
      CANx->RF1R = CAN_RF1R_FULL1;  
      break;
    case CAN_IT_FOV1:
      /* Clear CAN_RF1R_FOVR1 (rc_w1)*/
      CANx->RF1R = CAN_RF1R_FOVR1; 
      break;
    case CAN_IT_WKU:
      /* Clear CAN_MSR_WKUI (rc_w1)*/
      CANx->MSR = CAN_MSR_WKUI;  
      break;
    case CAN_IT_SLK:
      /* Clear CAN_MSR_SLAKI (rc_w1)*/ 
      CANx->MSR = CAN_MSR_SLAKI;   
      break;
    case CAN_IT_EWG:
      /* Clear CAN_MSR_ERRI (rc_w1) */
      CANx->MSR = CAN_MSR_ERRI;
       /* @note the corresponding Flag is cleared by hardware depending on the CAN Bus status*/ 
      break;
    case CAN_IT_EPV:
      /* Clear CAN_MSR_ERRI (rc_w1) */
      CANx->MSR = CAN_MSR_ERRI; 
       /* @note the corresponding Flag is cleared by hardware depending on the CAN Bus status*/
      break;
    case CAN_IT_BOF:
      /* Clear CAN_MSR_ERRI (rc_w1) */ 
      CANx->MSR = CAN_MSR_ERRI; 
       /* @note the corresponding Flag is cleared by hardware depending on the CAN Bus status*/
       break;
    case CAN_IT_LEC:
      /*  Clear LEC bits */
      CANx->ESR = RESET; 
      /* Clear CAN_MSR_ERRI (rc_w1) */
      CANx->MSR = CAN_MSR_ERRI; 
      break;
    case CAN_IT_ERR:
      /*Clear LEC bits */
      CANx->ESR = RESET; 
      /* Clear CAN_MSR_ERRI (rc_w1) */
      CANx->MSR = CAN_MSR_ERRI; 
       /* @note BOFF, EPVF and EWGF Flags are cleared by hardware depending on the CAN Bus status*/
       break;
    default:
       break;
   }
}
 /**
  * @}
  */

/**
  * @brief  Checks whether the CAN interrupt has occurred or not.
  * @param  CAN_Reg: specifies the CAN interrupt register to check.
  * @param  It_Bit: specifies the interrupt source bit to check.
  * @retval The new state of the CAN Interrupt (SET or RESET).
  */
static ITStatus CheckITStatus(uint32_t CAN_Reg, uint32_t It_Bit)
{
  ITStatus pendingbitstatus = RESET;
  
  if ((CAN_Reg & It_Bit) != (uint32_t)RESET)
  {
    /* CAN_IT is set */
    pendingbitstatus = SET;
  }
  else
  {
    /* CAN_IT is reset */
    pendingbitstatus = RESET;
  }
  return pendingbitstatus;
}

/**
  * @}
  */

/**
  * @}
  */

/**
  * @}
  */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/