tuber/desk/user/main.cpp

#include "stm32g4xx_hal.h"
#include "cmsis_os.h"
#include "i2c.h"
#include "terminal_user.h"
#include "terminal_usartbridge.h"
#include "control.h"
#include "oled_common.h"
#include "settings.h"
#include "uart_bridge.h"
#include <stdio.h>

void SystemClock_Config(void);
void Error_Handler(void);

static void MX_GPIO_Init(void);


void StartupTask(void const *params);
osThreadId startupTaskHandle;




int main()
{
    HAL_Init();
    
    SystemClock_Config();
    
    MX_GPIO_Init();
    
    //MX_I2C1_Init();
    
   
    osThreadDef(Startup, StartupTask, osPriorityNormal, 0, 2*128);
    startupTaskHandle = osThreadCreate(osThread(Startup), NULL);
    
    osKernelStart();
    
    return 0;
}


//
void StartupTask(void const *argument)
{
    MX_GPIO_Init();
      
    // Терминал
    sbsTerminal.configure();
            
    // USART терминал
    terminalUsartBridge.configure();
    
    // Настройки
    settings_crc_init();
    settings_load();
    
    //
    init_encoder();
    
    // Порт для связи с роботом и обработка данных
    ub_init_os();
    init_usart();
    
    // Дисплей
    init_oled();
#if 0    
    for (;;) {
        HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_6);
        osDelay(200);
        printf("hello world\r\n");
    }
#endif    
    vTaskDelete(NULL);
}


static void MX_GPIO_Init(void)
{
    GPIO_InitTypeDef GPIO_InitStruct = {0};
    
    /* GPIO Ports Clock Enable */
    __HAL_RCC_GPIOC_CLK_ENABLE();
    __HAL_RCC_GPIOF_CLK_ENABLE();
    __HAL_RCC_GPIOA_CLK_ENABLE();
    
    /*Configure GPIO pin Output Level */
    HAL_GPIO_WritePin(GPIOC, GPIO_PIN_6, GPIO_PIN_RESET);
    
    /*Configure GPIO pin : PC13 */
    GPIO_InitStruct.Pin = GPIO_PIN_13;
    GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
    
    /*Configure GPIO pin : PC6 */
    GPIO_InitStruct.Pin = GPIO_PIN_6;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
    HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
}


// 192.168.10.244
void SystemClock_Config(void)
{
    RCC_OscInitTypeDef RCC_OscInitStruct = {0};
    RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
    
    HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1_BOOST);
    
    HAL_PWR_EnableBkUpAccess();
    __HAL_RCC_LSEDRIVE_CONFIG(RCC_LSEDRIVE_LOW);
    
    RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48|RCC_OSCILLATORTYPE_HSE
                                |RCC_OSCILLATORTYPE_LSE;
    RCC_OscInitStruct.HSEState = RCC_HSE_ON;
    RCC_OscInitStruct.LSEState = RCC_LSE_ON;
    RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;
    RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
    RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
    RCC_OscInitStruct.PLL.PLLM = RCC_PLLM_DIV2;
    RCC_OscInitStruct.PLL.PLLN = 85;
    RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
    RCC_OscInitStruct.PLL.PLLQ = RCC_PLLQ_DIV2;
    RCC_OscInitStruct.PLL.PLLR = RCC_PLLR_DIV2;
    if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
    {
        Error_Handler();
    }
    
    RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                                |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
    RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
    RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
    RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
    RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
    
    if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4) != HAL_OK)
    {
        Error_Handler();
    }
}


//
void Error_Handler(void)
{
    __disable_irq();
    while (1) {}
}