muvie_string_controller/modules/adc.c

#include "stm32f0xx_hal.h"
#include "adc.h"
#include "led.h"
#include "tim.h"
#include <stdio.h>


#define VOLTAGE_FACTOR      0.000806 // 0.24194
#define FREQ_FACTOR         0.000806


ADC_HandleTypeDef       AdcHandle;
ADC_ChannelConfTypeDef  sConfig;

ADC_FILTER_t            adc_bat;
//ADC_FILTER_t            adc_freq;

adc_ufulter_t           adc_freq;

float                   bat_voltage = 0.0; 
uint16_t                freq_voltage = 0.0;        


__IO uint16_t   adc_values[2];


//
void adc_init(void)
{
    GPIO_InitTypeDef GPIO_InitStruct = {0};

    __HAL_RCC_GPIOA_CLK_ENABLE();
    __HAL_RCC_ADC1_CLK_ENABLE();

    GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1;
    GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
    
    
    AdcHandle.Instance          = ADC1;
    
    HAL_ADC_DeInit(&AdcHandle);
  
    AdcHandle.Init.ClockPrescaler        = ADC_CLOCK_SYNC_PCLK_DIV2;      /* Synchronous clock mode, input ADC clock with prscaler 2 */

    AdcHandle.Init.Resolution            = ADC_RESOLUTION_12B;            /* 12-bit resolution for converted data */
    AdcHandle.Init.DataAlign             = ADC_DATAALIGN_RIGHT;           /* Right-alignment for converted data */
    AdcHandle.Init.ScanConvMode          = ADC_SCAN_DIRECTION_FORWARD;    /* Sequencer disabled (ADC conversion on only 1 channel: channel set on rank 1) */
    AdcHandle.Init.EOCSelection          = ADC_EOC_SINGLE_CONV;           /* EOC flag picked-up to indicate conversion end */
    AdcHandle.Init.LowPowerAutoPowerOff  = DISABLE;
    AdcHandle.Init.LowPowerAutoWait      = DISABLE;                       /* Auto-delayed conversion feature disabled */
    AdcHandle.Init.ContinuousConvMode    = DISABLE;                        /* Continuous mode enabled (automatic conversion restart after each conversion) */
    AdcHandle.Init.DiscontinuousConvMode = ENABLE;                       /* Parameter discarded because sequencer is disabled */
    AdcHandle.Init.ExternalTrigConv      = ADC_SOFTWARE_START;            /* Software start to trig the 1st conversion manually, without external event */
    AdcHandle.Init.ExternalTrigConvEdge  = ADC_EXTERNALTRIGCONVEDGE_NONE; /* Parameter discarded because software trigger chosen */
    AdcHandle.Init.DMAContinuousRequests = ENABLE;                       /* ADC DMA continuous request to match with DMA circular mode */
    AdcHandle.Init.Overrun               = ADC_OVR_DATA_OVERWRITTEN;      /* DR register is overwritten with the last conversion result in case of overrun */
    AdcHandle.Init.SamplingTimeCommon    = ADC_SAMPLETIME_28CYCLES_5;
        
    HAL_ADC_Init(&AdcHandle);
  
    sConfig.Channel                      = ADC_CHANNEL_0;               /* Channel to be converted */
    sConfig.Rank                         = ADC_RANK_CHANNEL_NUMBER;
    HAL_ADC_ConfigChannel(&AdcHandle, &sConfig);
  
    sConfig.Channel                      = ADC_CHANNEL_1;               /* Channel to be converted */
    HAL_ADC_ConfigChannel(&AdcHandle, &sConfig);
    
    HAL_ADCEx_Calibration_Start(&AdcHandle);
    
    adc_dma_init(&AdcHandle);
    
    //HAL_ADC_Start(&AdcHandle);
}


void adc_dma_init(ADC_HandleTypeDef *hadc)
{
    static DMA_HandleTypeDef  DmaHandle;

    __HAL_RCC_DMA1_CLK_ENABLE();
  
    DmaHandle.Instance = DMA1_Channel1;

    DmaHandle.Init.Direction           = DMA_PERIPH_TO_MEMORY;
    DmaHandle.Init.PeriphInc           = DMA_PINC_DISABLE;
    DmaHandle.Init.MemInc              = DMA_MINC_ENABLE;
    DmaHandle.Init.PeriphDataAlignment = DMA_PDATAALIGN_HALFWORD;   /* Transfer from ADC by half-word to match with ADC configuration: ADC resolution 10 or 12 bits */
    DmaHandle.Init.MemDataAlignment    = DMA_MDATAALIGN_HALFWORD;   /* Transfer to memory by half-word to match with buffer variable type: half-word */
    DmaHandle.Init.Mode                = DMA_CIRCULAR;              /* DMA in circular mode to match with ADC configuration: DMA continuous requests */
    DmaHandle.Init.Priority            = DMA_PRIORITY_HIGH;
  
    HAL_DMA_DeInit(&DmaHandle);
    HAL_DMA_Init(&DmaHandle);

    __HAL_LINKDMA(hadc, DMA_Handle, DmaHandle);
  
    HAL_NVIC_SetPriority(DMA1_Channel1_IRQn, 1, 0);
    HAL_NVIC_EnableIRQ(DMA1_Channel1_IRQn);
}


//
float adc_average(ADC_FILTER_t *flt, float new_value)
{
    if (!(flt->head < ADC_FILTER_LEN))
        flt->head = 0;

    if (flt->count < ADC_FILTER_LEN)
        flt->count++;

    flt->sum -= flt->buf[flt->head];
    flt->sum += new_value;
    flt->buf[flt->head++] = new_value;
  
    return flt->sum/(flt->count);
}


//
uint16_t adc_average_uint(adc_ufulter_t *flt, uint16_t new_value)
{
    if (!(flt->head < ADC_FILTER_LEN))
        flt->head = 0;

    if (flt->count < ADC_FILTER_LEN)
        flt->count++;

    flt->sum -= flt->buf[flt->head];
    flt->sum += new_value;
    flt->buf[flt->head++] = new_value;
  
    return flt->sum/(flt->count);
}


//
void adc_task(void)
{
    HAL_ADC_Start_DMA(&AdcHandle, (uint32_t *)adc_values, 2);
    HAL_ADC_Start(&AdcHandle);
    
#if 0  
    bat_voltage = 2*adc_average(&adc_bat, HAL_ADC_GetValue(&AdcHandle) * ADC_FACTOR);
    
    if (bat_voltage > 3.4)
        led_but_on();
    else
        led_but_toggle();
#endif    
}


//
void adc_print_data(void)
{
    printf("%f %u\r\n", bat_voltage, freq_voltage);
}


void DMA1_Channel1_IRQHandler(void)
{
    HAL_DMA_IRQHandler(AdcHandle.DMA_Handle);
}


void HAL_ADC_ConvCpltCallback(ADC_HandleTypeDef *AdcHandle)
{
    bat_voltage = adc_average(&adc_bat, adc_values[0] * VOLTAGE_FACTOR);
    
    // Для получения значения в вольтах
    //freq_voltage = adc_average(&adc_freq, adc_values[1] * FREQ_FACTOR);
    
    freq_voltage = adc_average_uint(&adc_freq, adc_values[1]);
    
    tim_set_string_freq();
}